We regularly update articles related to the manufacturing industry.
Alodine coating, also known as chem film or chromate conversion coating, is a chemical treatment applied to aluminum. It creates a protective shield on aluminum parts. The primary purpose is to prevent corrosion, which can weaken metal parts over time. Additionally, it prepares the surface for painting or other finishes by improving adhesion.
A blind hole is a hole drilled, milled, or bored into a material that doesn’t penetrate through to the other side. Unlike through holes, blind holes have a defined depth and a bottom surface. They are commonly used in applications where a fastener or component needs to sit flush or be hidden within the material.
Centerless grinding is a material reduction process that uses a grinding wheel to remove material from the outer diameter of a workpiece. It uses a spinning abrasive wheel to cut material from the outside of a workpiece. Unlike other methods, it doesn’t need clamps or centers to hold the piece in place.
Because it doesn’t require centering, setup is faster and more efficient. It also gives better roundness and precision in the final product. The process allows tight control over the speed and movement of the workpiece, which helps achieve very accurate results.
Aluminum milling requires specific approaches that are different from other metals. The right combination of cutting tools, speeds, feeds, and cooling methods can dramatically improve your results. You can achieve excellent surface finishes with proper technique while extending tool life and maintaining tight tolerances across your projects.
A typical welding defect is the undercut. This occurs when the weld does not adequately cover the base metal. This flaw could significantly weaken structural integrity, making the weld joint more vulnerable to failure.
Bevel welding is the process of preparing metal for welding, usually by cutting a bevel into the edge of the metal. A bevel weld joins two metal pieces where one or both edges are cut at an angle. This creates a groove that allows better access for the welding electrode and results in stronger joints.
Unlike simple fillet welds, bevel welds are used when the metal thickness exceeds 3/8 inch (9.5mm). The angled cut allows full penetration through thick materials.
Plasma cutting uses ionized gas to form a high-temperature channel that cuts through metal. This method offers a good balance between cut quality and cost for stainless steel. It works well for both prototypes and large production runs. The edges are cleaner than those from oxy-fuel cutting. Plasma cutting is also more budget-friendly than laser cutting and suitable for many uses.
Phosphating is a chemical process in which a phosphate coating is applied to a metal surface. This coating is a difficult-to-dissolve transformation layer composed of metal phosphates. It acts as a protective layer, shielding the metal from corrosion, wear, and other environmental damage.
Phosphating works through chemical reactions between the metal surface and a phosphate solution. When the metal is immersed in the solution, the phosphoric acid reacts with the metal ions to form a layer of insoluble phosphate crystals.
E-Coating, or Electrophoretic Deposition, refers to a specific type of paint applied to metal parts. It involves immersing the parts in a bath of paint particles suspended in water. When we apply an electric charge, the paint particles stick to the metal surface.
Getting good results when grinding stainless steel starts with choosing the right tools and methods. Use aluminum oxide or ceramic abrasives made explicitly for stainless steel. Keep the metal cool during grinding to avoid heat discoloration. Work with light to medium pressure and move constantly to prevent overheating one area.
Metal burrs can be small and sharp protrusions on metal edges after machining operations such as drilling or milling. These are bits of metal that have not been removed cleanly from a part. They can leave a jagged or rough edge.
A welding fixture is a device or tool used to hold and position workpieces during welding. It ensures parts stay aligned correctly, making the welding process more accurate and efficient. These fixtures are used in manual and automated welding for precise and repeatable results.
A fly cutter is a rotary cutting tool that attaches to a milling machine spindle and rotates to remove material. The cutting bit extends from the tool body and cuts in an arc pattern with each rotation, creating a smooth, flat surface.
The tool creates flat surfaces because the cutting edge is set at a consistent height. Each pass removes a thin material layer, and the milling machine’s feed movement creates a flat surface. This process is sometimes called “fly cutting” because of the cutting edge’s sweeping motion.
Springback refers to a material’s tendency to revert to its original shape after being bent. When force bends the metal, it deforms both elastically and plastically. After the force is removed, the elastic part tries to recover. This rebound is what we call springback.
Welding defects can affect a weld’s strength, durability, and appearance. Cracks, porosity, and inclusions are some of the most common types. Other types include lack of fusion or penetration, undercuts, overlaps, weld mismatches, excessive penetration, and distortion. By identifying and preventing them, you can improve the appearance and strength of your welds.
Electrical Discharge Machining (Sinker EDM) is a metal removal process that uses electrical sparks to remove material from the workpiece. This process involves submerging the electrode and the workpiece in dielectric fluid. High-frequency electrical pulses then erode and melt the surface of the piece.
We will contact you within 1 working day, please pay attention to the email with the suffix”@goodsheetmetal.com”
